Hardware Platforms

Supported Sensor Boards

This library supports almost the complete XENSIV™ 3D Magnetic Sensors Tlx493d family. This includes the Shield2Go boards, as well as the 2GO Kits of the sensors. Following you will see a list of boards which are supported by this library.

XENSIV™ TLV493D-A1B6 Shield2Go

Pinout Diagram

Pin Description

Pin Name	Description
3V3	3.3 V supply input
VDD	Power supply pin - do not apply more than 3.3 V
GND	Supply and signal ground
SCL	Serial clock line of the I2C bus
SDA	Serial data line of the I2C bus

XENSIV™ TLV493D-A1B6 2GO Kit

Pinout Diagram

Pin Description

Pin Name	Description
3V3	3.3 V supply input
VDD	Power supply pin - do not apply more than 3.3 V
GND	Supply and signal ground
SCL	Serial clock line of the I2C bus
SDA	Serial data line of the I2C bus
TX	UART transmit pin
RX	UART receive pin
MISO	MISO pin of the SPI bus
MOSI	MOSI pin of the SPI bus
SCK	Clock pin of the SPI bus
SS	Slave select pint of the SPI bus
GPIO / 4	General purpose pin (Arduino pin number 4)
GPIO / 5	General purpose pin (Arduino pin number 5)
PWM0 / 8	Pulse-width modulation pin 0 (Arduino pin number 8)
INT / 9	Interrupt pin (Arduino pin number 9)
A1 / 12	Analog pin 1 (Arduino pin number 12)
A2 / 13	Analog pin 2 (Arduino pin number 13)

XENSIV™ TLE493D-W2B6 Shield2Go

Product Page - XENSIV™ TLE493D-W2B6 Shield2Go

Pinout Diagram

Pin Description

Pin Name	Description
3V3	3.3 V supply input
VDD	Power supply pin - do not apply more than 3.3 V
GND	Supply and signal ground
SCL	Serial clock line of the I2C bus
SDA	Serial data line of the I2C bus
INT / GPIO3	Interrupt pin

XENSIV™ TLE493D-W2B6 2GO Kit

Pinout Diagram

Pin Description

Pin Name	Description
3V3	3.3 V supply input
VDD	Power supply pin - do not apply more than 3.3 V
GND	Supply and signal ground
SCL	Serial clock line of the I2C bus
SDA	Serial data line of the I2C bus
TX	UART transmit pin
RX	UART receive pin
MISO	MISO pin of the SPI bus
MOSI	MOSI pin of the SPI bus
SCK	Clock pin of the SPI bus
SS	Slave select pint of the SPI bus
GPIO / 4	General purpose pin (Arduino pin number 4)
GPIO / 5	General purpose pin (Arduino pin number 5)
PWM0 / 8	Pulse-width modulation pin 0 (Arduino pin number 8)
INT / 9	Interrupt pin (Arduino pin number 9)
A1 / 12	Analog pin 1 (Arduino pin number 12)
A2 / 13	Analog pin 2 (Arduino pin number 13)

XENSIV™ TLI493D-W2BW Shield2Go

Pinout Diagram

Pin Description

Pin Name	Description
3V3	3.3 V supply input
VDD	Power supply pin - do not apply more than 3.3 V
GND	Supply and signal ground
SCL	Serial clock line of the I2C bus
SDA	Serial data line of the I2C bus
RST / GPIO2	Power control pin
INT / GPIO3	Interrupt pin

XENSIV™ TLE493D-P2B6 2GO Kit

Pinout Diagram

Pin Description

Pin Name	Description
3V3	3.3 V supply input
VDD	Power supply pin - do not apply more than 3.3 V
GND	Supply and signal ground
SCL	Serial clock line of the I2C bus
SDA	Serial data line of the I2C bus
TX	UART transmit pin
RX	UART receive pin
MISO	MISO pin of the SPI bus
MOSI	MOSI pin of the SPI bus
SCK	Clock pin of the SPI bus
SS	Slave select pint of the SPI bus
GPIO / 4	General purpose pin (Arduino pin number 4)
GPIO / 5	General purpose pin (Arduino pin number 5)
PWM0 / 8	Pulse-width modulation pin 0 (Arduino pin number 8)
INT / 9	Interrupt pin (Arduino pin number 9)
A1 / 12	Analog pin 1 (Arduino pin number 12)
A2 / 13	Analog pin 2 (Arduino pin number 13)

Additional Supported Sensors

This library also supports the two following sensor variants: * TLE493D A2B6 * TLI493D A2B6 * TLV493D A2BW Since they are not available as Kit2Go or as Shield2Go we just listed them here, but they are supported by library. If you want to use one of these sensors in your project please refer to the corresponding data sheet for a pinout of the sensor.

Supported MCU Platforms

In principle, the library can be used with any Arduino compatible MCU platform, as long as its Arduino core is implemented with the Arduino Reference Language. Below you will find a list of the boards which should be compatible with the library.

MCU Platforms
XMC 2Go
XMC1100 Boot Kit
XMC4700 Relax Kit
XMC4700 Relax Lite Kit
Arduino Uno Rev3
Arduino Uno R4 Minima

Verified MCU and Sensor Combinations

In the following table you find an extensive list of examples we have verified. For each example we also mentioned the used MCU board. Please be aware that we can only guarantee that the library fully functions with these MCU and sensor combinations. But all the examples should work with any of the MCU boards mentioned above and the corresponding senors of these examples.

Warning

Some of the examples have been tested with experimental boards. This means that you cannot buy these boards directly from Infineon. If you’re really interested to try out these examples, you can order one of the available boards with the same sensor package and replace the sensor on the board with the desired one.

Status	Board Type	Sensor	Tests	Comment
pass	Kit2Go	A1B6	Test suite, read_icc	arduino-cli 0.34.0 wih xmc 2.2.0.
pass	Kit2Go	A2B6	Test suite, read_icc	arduino-cli 0.34.0 wih xmc 2.2.0.
pass	Kit2Go	P2B6	Test suite, read_icc	arduino-cli 0.34.0 wih xmc 2.2.0.
pass	Kit2Go	W2B6	Test suite, read_icc	arduino-cli 0.34.0 wih xmc 2.2.0.
pass	Kit2Go	P3I8	Test suite, read_spi_sensor	arduino-cli 0.34.0 wih xmc 2.2.0. Experimental board, which is not for sale yet.
pass	S2Go	A1B6	read_iic_a1b6_extended_addresses	arduino-cli 0.34.0 wih xmc 2.2.0.
pass	S2Go	A2BW	Test suite	arduino-cli 0.34.0 wih xmc 2.2.0. Experimental board with W2B6 as base board. Not for sale.
pass	S2Go	W2B6	Test suite	arduino-cli 0.34.0 wih xmc 2.2.0.
pass	S2Go	W2BW	Test suite	arduino-cli 0.34.0 wih xmc 2.2.0.
pass	XMC4700 Relax Kit Lite	W2BW, W2B6, P3B6	read_3_different_iic_sensors	arduino-cli 0.34.0 wih xmc 2.2.0.
pass	XMC4700 Relax Kit Lite	W2B6	read_3_equal_iic_sensors	arduino-cli 0.34.0 wih xmc 2.2.0.
pass	XMC4700 Relax Kit Lite	W2BW	read_iic_sensor_with_wakeup	arduino-cli 0.34.0 wih xmc 2.2.0.
pass	S2Go	P3B6	Test suite	arduino-cli 0.34.0 wih xmc 2.2.0. Experimental board with W2B6 as base board. Not yet for sale.
pass	Uno R3	W2B6	read_iic	arduino-cli 0.34.0 with AVR 1.8.6 and Arduino IDE 2.3.2
pass	Uno R3	W2BW	read_iic	arduino-cli 0.34.0 with AVR 1.8.6 and Arduino IDE 2.3.2
pass	Uno R4 Minima	W2BW	Test suite, read_iic	arduino-cli 0.34.0 with UNO R4 and Arduino IDE 2.3.2